HCD 皇冠深孔鏟鑽刀片
產品特點
型號 : HCD
皇冠深孔鏟鑽刀片
皇冠深孔鏟鑽刀片
| 每隔0.1mm | ||
| 8 ~ 9.99 | 24 ~ 25.99 | |
| 10 ~ 11.99 | 26 ~ 27.99 | |
| 12 ~ 13.99 | 28 ~ 29.99 | |
| 14 ~ 15.99 | 30 ~ 31.99 | |
| 16 ~ 17.99 | 32 ~ 33.99 | |
| 18 ~ 19.99 | 34 ~ 35.99 | |
| 20 ~ 21.99 | 36 ~ 37.99 | |
| 22 ~ 23.99 | 38 ~ 40 | |
| 皇冠鑽硬質合金 KPM45-P (通用槽型) 鑽尖 切削參數 | ||||||||||||
| Crown Drill Solid Carbide KPM45-P (General Slot Type) Drill Point Cutting Parameters | ||||||||||||
| 材料分組 Material grouping | 切削速度 VC cutting speed-vc (m/min) | 單位 Unit | 根據直徑推薦進給率 (Fr) Feed rate (Fr) recommended according to diameter | |||||||||
| 最小值 Min | 最中值 Median | 最大值 Max | φ8-12.5 | φ12.5-16 | φ16-20 | φ20-25.4 | φ25.4-32 | φ32-40 | φ40 | |||
| P | 1 | 100 | 110 | 120 | mm/轉 | 0.05-0.18 | 0.15-0.31 | 0.17-0.36 | 0.19-0.41 | 0.25-0.53 | 0.29-0.60 | 0.33-0.69 |
| 2 | 80 | 95 | 110 | mm/轉 | 0.05-0.18 | 0.15-0.31 | 0.17-0.36 | 0.19-0.41 | 0.25-0.53 | 0.29-0.60 | 0.33-0.69 | |
| 3 | 65 | 70 | 80 | mm/轉 | 0.05-0.18 | 0.15-0.31 | 0.17-0.36 | 0.19-0.41 | 0.25-0.53 | 0.29-0.60 | 0.33-0.69 | |
| 4 | 55 | 65 | 75 | mm/轉 | 0.05-0.17 | 0.15-0.28 | 0.14-0.30 | 0.16-0.36 | 0.20-0.46 | 0.23-0.53 | 0.30-0.60 | |
| 5 | 50 | 55 | 65 | mm/轉 | 0.05-0.17 | 0.09-0.15 | 0.11-0.18 | 0.12-0.21 | 0.15-0.25 | 0.17-0.29 | 0.20-0.32 | |
| 6 | 45 | 50 | 65 | mm/轉 | 0.05-0.16 | 0.12-0.23 | 0.14-0.26 | 0.17-0.30 | 0.20-0.38 | 0.24-0.43 | 0.26-0.54 | |
| M | 1 | 30 | 60 | 90 | mm/轉 | 0.03-0.09 | 0.09-0.14 | 0.11-0.20 | 0.13-0.20 | 0.16-0.25 | 0.18-0.28 | 0.21-0.31 |
| 2 | 30 | 50 | 90 | mm/轉 | 0.03-0.09 | 0.09-0.14 | 0.11-0.20 | 0.13-0.20 | 0.16-0.25 | 0.18-0.28 | 0.21-0.31 | |
| 3 | 20 | 40 | 60 | mm/轉 | 0.03-0.09 | 0.09-0.14 | 0.11-0.20 | 0.13-0.20 | 0.16-0.25 | 0.18-0.28 | 0.21-0.31 | |
| 皇冠鑽硬質合金 KMS35-S (不銹鋼槽型) 鑽尖 切削參數 | ||||||||||||
| Crown Drill Solid Carbide KMS35-S (Stainless Steel Slot Type) Drill Point Cutting Parameters | ||||||||||||
| 材料分組 Material grouping | 切削速度 VC cutting speed-vc (m/min) | 單位 Unit | 根據直徑推薦進給率 (Fr) Feed rate (Fr) recommended according to diameter | |||||||||
| 最小值 Min | 最中值 Median | 最大值 Max | φ8-12.5 | φ12.5-16 | φ16-20 | φ20-25.4 | φ25.4-32 | φ32-40 | φ40 | |||
| P | 1 | 110 | 140 | 170 | mm/轉 | 0.05-0.18 | 0.15-0.31 | 0.17-0.36 | 0.19-0.41 | 0.25-0.53 | 0.29-0.60 | 0.33-0.69 |
| 2 | 100 | 120 | 140 | mm/轉 | 0.05-0.18 | 0.15-0.31 | 0.17-0.36 | 0.19-0.41 | 0.25-0.53 | 0.29-0.60 | 0.33-0.69 | |
| 3 | 80 | 100 | 120 | mm/轉 | 0.05-0.18 | 0.15-0.31 | 0.17-0.36 | 0.19-0.41 | 0.25-0.53 | 0.29-0.60 | 0.33-0.69 | |
| M | 1 | 40 | 60 | 80 | mm/轉 | 0.03-0.09 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 | 0.18-0.28 | 0.21-0.31 |
| 2 | 35 | 55 | 70 | mm/轉 | 0.03-0.09 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 | 0.18-0.28 | 0.21-0.31 | |
| 3 | 20 | 40 | 60 | mm/轉 | 0.03-0.09 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 | 0.18-0.28 | 0.21-0.31 | |
| N | 1 | 90 | 155 | 220 | mm/轉 | 0.07-0.20 | 0.18-0.36 | 0.20-0.44 | 0.24-0.50 | 0.28-0.56 | 0.32-0.65 | 0.32-0.70 |
| 2 | 90 | 155 | 220 | mm/轉 | 0.07-0.20 | 0.18-0.36 | 0.20-0.44 | 0.24-0.50 | 0.28-0.56 | 0.32-0.65 | 0.32-0.70 | |
| 3 | 80 | 120 | 160 | mm/轉 | 0.07-0.20 | 0.18-0.36 | 0.20-0.44 | 0.24-0.50 | 0.28-0.56 | 0.32-0.65 | 0.32-0.70 | |
| 4 | 90 | 155 | 220 | mm/轉 | 0.07-0.20 | 0.18-0.36 | 0.20-0.44 | 0.24-0.50 | 0.28-0.56 | 0.32-0.65 | 0.32-0.70 | |
| S | 1 | 20 | 40 | 60 | mm/轉 | 0.02-0.08 | 0.05-0.10 | 0.07-0.12 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 |
| 2 | 15 | 30 | 45 | mm/轉 | 0.02-0.08 | 0.05-0.10 | 0.07-0.12 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 | |
| 3 | 15 | 30 | 45 | mm/轉 | 0.02-0.08 | 0.05-0.10 | 0.07-0.12 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 | |
| 4 | 10 | 25 | 40 | mm/轉 | 0.02-0.08 | 0.05-0.10 | 0.07-0.12 | 0.09-0.14 | 0.11-0.17 | 0.13-0.20 | 0.16-0.25 | |
台中市大甲區開元路21號｜統編：28539446
886-4-26865253 
886-4-26882279
